Irricad

Please see this post :-

viewtopic.php?t=1002

Phil

Hi

The error can only happen when trying to “Save As Copy” in the database editor and it means that one of the installed files (either Skeleton.mdb or
Skeleton.accdb) is missing. Renewing your lease licence won't have removed these files and they are contained in the standard installations so the ...

I'm sure you will have done this already but it is worth noting that all the design/analysis processes will need to be rerun after any changes to elevations in a design (such as adding them). The design processes (and the checks Jabes mentions) will automatically re-interpolate the elevations.

The ...

The -1 indicates that an error was encountered when trying to calculate the running costs. The most common cause of this is if mainline design/analysis hasn't been run, this is required before the running costs can be calculated.

Phil

See the attached PDF file.

Regards

Phil

There are a number of possible causes, please look at these two posts on the forum:-

https://www.irricad.com/phpbb3/viewtopic.php?t=922

https://www.irricad.com/phpbb3/viewtopic.php?t=461

Additionally please check and confirm if you are able to open IRRICAD from the desktop shortcut (i.e. into a ...

Hi

One approach would be to use Mainline demand points to represent each zone in terms of flow and required pressure. You may also need to fully draw and design a small number of zones to determine the requirements for the demand points, if these aren't known. Note that in these types of design ...

Hi

From your description I think that using "unconnected" spraylines (or sprayline block) will allow you to do what you wish. Have a look at the "Help topics" in the program for more information, or contact your local support.

Regards

Phil

Hi

Unfortunately an enhancement to another feature, in Link V20, inadvertently caused this problem. Our apologies for the oversight, we will fix thing and it will appear in the next patch. Until then the only solutions are:-

1) Convert each polyline individually (i.e. select only 1 at a time to ...

Hi Chris

IRRICAD Link installs MS Access drivers but it's unnecessary to have Office 365 (or MS Access) or upgrade either to run Link. The post above mentions that if you DO have Office 365 then an upgrade can "break" the drivers that IRRICAD uses (although we made changes to V19 Link to make the ...

Hi Jeremy

Yes it is possible to do this (assuming you mean a single regulator that is in-line in the sub-main). The process is relatively easy:-

1) Add the regulator (if it isn't already there) into the "Other Hydraulic" tab of your database and set the fitting type to PRV (see the IRRICAD ...

Hi Steve

This looks like some sort of folder/file security issue. When IRRICAD is installed it sets up permissions on for the installed folder so that the Errorlog.txt file (and others) can be created and written to (I'm not sure how this would have changed). You can check this by simply right ...

Hi

The problem you describe indicates that some of the internal design files have been deleted (this is where the missing information is stored). Did you save and re-open the design after calculating the original pressures and before you next viewed the Zone Design Configuration?

If so then please ...

A new patch is now available for Standalone V19 (19.11)
To apply, go to Help|Check for Updates in IRRICAD V19 and then to proceed, click [Next]. The upgrade will be downloaded and installed.

Alternatively simply go to https://www.irricad.com/upgrades-patches/ and follow the instructions to download ...

Hi Jabes

Yes all versions of IRRICAD take 3D lengths into consideration in the design process and BOM/costing.

Regards

Phil

It is possible to place pumps in looped parts of systems but it is not recommended because of the following:-

To simplify the user interface the direction of flow through a pump does not need to be specified by the user. When analyzing branched systems (or branched sections of looped systems) the ...

The use of IRRICAD Link (or standalone) is controlled by the dongle so there is no licence to transfer (simply install Link and plug the dongle into the other computer).

Note that you probably will need to transfer the licence of the CAD host program (AutoCAD or BricsCAD). This is normally done in ...

Hi

I think that your problem will have been caused by an update to Office 2010, please see this post for instructions on how to rectify it:-

http://www.irricad.com/phpbb3/viewtopic.php?f=26&t=599&p=1394&hilit=FixAccessDatabaseEngine#p1394

Note that this will affect all IRRICAD DWG files.

If you ...

Detailed analysis requires that the control valve pressure is specified and this warning indicates that this hasn't been done. Control Valve pressures for each zone may be entered in "Design/Zone Design Configuration" - more information is available in the IRRICAD manual ("Help/Help Topics").

Note ...

Running "Interpolate Elevations" from the "Design" menu will re-create the DEM but obviously this will take account of any existing IRRICAD contours or spot heights. As previously mentioned unless your GPS data has been imported via the "Import Contours" function it cannot effect the DEM. If it was ...